kevkid
LV1 Newcomer (Next: 20)
 Offline
Last Login: 03 November, 2012, 23:42:57
Date Registered: 28 February, 2012, 05:20:12
Posts: 10
Topic starter
Total Post Ratings: 0
|
 |
« on: 29 July, 2012, 08:51:32 » |
0
|
Is this possible, I have been trying for a while but I continue to get the error: retrying. I am guessing that the calculator will not accept the boot2 from my computer when trying to send via Xmodem. I am using hyperterminal and it just gives me an error when I try to send the file, it never gets past 0 percent. I am not sure why it refuses to do this. I get to the poing where it says ready to Download boot2 then it will not accept the file it just retries until it reboots. Can anyone give advice?
Kevin Lopez
|
|
|
|
|
Logged
|
|
|
|
critor
Editor
LV10 31337 u53r (Next: 2000)
Offline
Gender: 
Last Login: Yesterday at 23:09:31
Date Registered: 14 July, 2009, 23:57:37
Location: Aix-Marseille, France
Posts: 1724
Total Post Ratings: +370
|
|
« Reply #1 on: 29 July, 2012, 18:06:57 » |
0
|
Is you board using the TTL standard, which is not 'really' RS232 ? (different voltages)
|
|
|
|
|
Logged
|
|
|
|
kevkid
LV1 Newcomer (Next: 20)
Offline
Last Login: 03 November, 2012, 23:42:57
Date Registered: 28 February, 2012, 05:20:12
Posts: 10
Topic starter
Total Post Ratings: 0
|
|
« Reply #2 on: 30 July, 2012, 06:11:32 » |
0
|
I am almost certain it does, I get console output from the calculator, but for some reason every time I try to upload the boot2 to the calculator, it fails and tries to retry sending the packet until it shuts down. Would the voltages matter if you get console output? It doesn't seem like it fried anything.
Kevin Lopez
|
|
|
|
|
Logged
|
|
|
|
ExtendeD
Coder Of Tomorrow
LV8 Addict (Next: 1000)
Offline
Gender:
Last Login: Today at 02:41:25
Date Registered: 02 January, 2010, 13:03:41
Location: France
Posts: 766
Total Post Ratings: +151
|
|
« Reply #3 on: 30 July, 2012, 07:57:20 » |
0
|
I couldn't use HyperTerminal, I had the same problem. Did you try lrzsz ? http://hackspire.unsads.com/wiki/index.php/Hardware#RS232 |
|
|
|
|
Logged
|
|
|
|
kevkid
LV1 Newcomer (Next: 20)
Offline
Last Login: 03 November, 2012, 23:42:57
Date Registered: 28 February, 2012, 05:20:12
Posts: 10
Topic starter
Total Post Ratings: 0
|
|
« Reply #4 on: 01 August, 2012, 16:39:06 » |
0
|
Thank you very much it worked, a little bit of a hassle to get it to transfer but all is well.
--Kevin Lopez
|
|
|
|
|
Logged
|
|
|
|
|
Powered by SMF 1.1.18 |
SMF © 2013, Simple Machines
