Author Topic: ndless 3.1 install?  (Read 12471 times)

0 Members and 1 Guest are viewing this topic.

Offline nicklite97

  • LV1 Newcomer (Next: 20)
  • *
  • Posts: 9
  • Rating: +0/-0
    • View Profile
Re: ndless 3.1 install?
« Reply #15 on: June 01, 2014, 03:23:24 pm »
How does a switching pack work?

Offline Hayleia

  • Programming Absol
  • Coder Of Tomorrow
  • LV12 Extreme Poster (Next: 5000)
  • ************
  • Posts: 3367
  • Rating: +393/-7
    • View Profile
Re: ndless 3.1 install?
« Reply #16 on: June 01, 2014, 03:49:34 pm »
Once installed, you can reboot your calc as usual or rename a "phoenix_old" file into "phoenix" and when rebooting, your calc will boot the other OS so you'll be able to switch between two OSes.
I own: 83+ ; 84+SE ; 76.fr ; CX CAS ; Prizm ; 84+CSE
Sorry if I answer with something that seems unrelated, English is not my primary language and I might not have understood well. Sorry if I make English mistakes too.

click here to know where you got your last +1s

Offline Dan Powers

  • LV1 Newcomer (Next: 20)
  • *
  • Posts: 5
  • Rating: +0/-0
    • View Profile
Re: ndless 3.1 install?
« Reply #17 on: November 09, 2014, 02:18:17 am »
the os installation is stuck 60% It wont install its it because my cx has cas installed?
same here.

Once installed, you can reboot your calc as usual or rename a "phoenix_old" file into "phoenix" and when rebooting, your calc will boot the other OS so you'll be able to switch between two OSes.
you could run two os??? could you run CAS v 3.1 and CX v 3.6? on the same device without reinstallation?
« Last Edit: November 09, 2014, 02:21:03 am by Dan Powers »

Offline FrancoDN

  • LV0 Newcomer (Next: 5)
  • Posts: 3
  • Rating: +0/-0
    • View Profile
Re: ndless 3.1 install?
« Reply #18 on: July 04, 2015, 08:25:51 pm »
I have a TI Nspire CX nonCAS hardware version D boot1 3.0.99 boot2 3.10.16 running a working CAS OS 3.1.0.392
I would like to Ndless it.

If I send to my calculator the .tcc installer the computer tells me it’s a “wrong handled type for the OS being sent”.
If I send to my calculator the .tco installer the OS installation goes forever, it never ends, there is a window in the Student Software with a loading bar that does not move on from 60%.

Is there a way I could proceed??

Regards.

Offline Vogtinator

  • LV9 Veteran (Next: 1337)
  • *********
  • Posts: 1193
  • Rating: +108/-5
  • Instruction counter
    • View Profile
Re: ndless 3.1 install?
« Reply #19 on: July 05, 2015, 08:29:47 am »
nlaunch has it's own ndless installer, just put ndless_resources.tns into /ndless and reboot.
BTW: This topic is fairly old, you should make a new one and/or let someone move your post into a new topic.

Offline FrancoDN

  • LV0 Newcomer (Next: 5)
  • Posts: 3
  • Rating: +0/-0
    • View Profile
Re: ndless 3.1 install?
« Reply #20 on: July 05, 2015, 09:46:13 am »
nlaunch has it's own ndless installer, just put ndless_resources.tns into /ndless and reboot.

Thanks Vog. That was all needed  :banghead:

Regards!!